How to Replace a Tub Yourself: Removing as well as Replacing.
How to Replace a Tub Yourself: Removing as well as Replacing.
Blog Article
We've stumbled upon this post relating to How to Install a Bathtub Yourself directly below on the internet and felt it made perfect sense to talk about it with you on my blog.
Installing a bathtub isn't precisely brain surgery, yet it does call for strong plumbing, carpentry, and also often, tiling abilities. Changing an old bath tub with a brand-new one is likewise a moderately challenging project. If the old tub is readily available, the job can move rapidly; if you have to open a wall to eliminate the old bathtub and also place the new bathtub, the task is much harder. In either case, the job is within a house handyman's skills, although you will require an assistant to move out the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the job and fit trying it. As opposed to working with a service provider to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you might require an expert plumber to make tube links.
This post will assist you install a new bath tub in your washroom if you have actually already purchased a new bathtub and also don't need to change the setup of your previous water pipelines.
Your tools and also product list ought to comprise the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of removing the existing taps can be fairly bothersome due to the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipes have been gotten rid of, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin ensuring that the washers remain in place between the faucet and also the sink. Secure the faucet in place with the maker supplied backnut. When the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind must be linked to the tap finishes initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Tub
Utilizing the two wood boards under its feet, position the bath tub in the called for position. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four tiny points.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the level checks out degree.
To mount taps, fit the bottom of the furthest flexible faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Turn on the supply of water and also examine all joints and also brand-new pipework for leakages and also tighten them if needed. Fill up the tub and also check the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling and also securing around the tub ought to wait till the bath tub has actually been utilized at least when as this will certainly settle it right into its final position.
Preparing for the Installment
Firstly, the sustaining structure supplied with the bath should be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a stiff seal, causing the water to permeate the wall in between the bath as well as the tiling, leading to difficulties with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Remember to always load the tub with water before sealing, to enable the movement experienced when the bathtub remains in usage. The sealant can fracture fairly very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently offered on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that blog entry on How to Install a Bathtub while doing a lookup on the search engines. Sharing is caring. One never knows, you may very well be helping someone out. Thank you for your time. Visit us again soon.
View Website Report this page